Gloss Aluminium – Storm Grey GAL10 – Design lakovaného hliníku.
Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
Gloss Aluminium – Storm Grey GAL10 – Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8″* 708,6″, 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
Settings | Gloss Aluminium - Storm Grey GAL10 remove | Gloss Aluminium - Leaf Green GAL07 remove | Gloss Aluminium - Olympic Blue GAL13 remove | Gloss Aluminium - Silver Mist GAL11 remove | Gloss Aluminium - True Blood GAL01 remove | Gloss Aluminium - Mermaid Green GAL05 remove |
---|---|---|---|---|---|---|
Image | ||||||
SKU | GAL10 | GAL07 | GAL13 | GAL11 | GAL01 | GAL05 |
Rating | ||||||
Cena | 16 276 Kč | 16 276 Kč | 16 276 Kč | 16 276 Kč | 16 276 Kč | 16 276 Kč |
Stock | Skladem
| Skladem
| Skladem
| Skladem
| Skladem
| Skladem
|
Availability | Skladem | Skladem | Skladem | Skladem | Skladem | Skladem |
Add to cart | ||||||
Description | Gloss Aluminium - Storm Grey GAL10 - Design lakovaného hliníku. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. | Gloss Aluminium - Leaf Green GAL07 - Design lakovaného hliníku. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. | Gloss Aluminium - Olympic Blue GAL13 - Design lakovaného hliníku. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. | Gloss Aluminium - Silver Mist GAL11 - Design lakovaného hliníku. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. | Gloss AluminiumTrue Blood GAL01 Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. | Gloss Aluminium - Mermaid Green GAL05 - Design lakovaného hliníku. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní. Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu. |
Content | Gloss Aluminium - Storm Grey GAL10 - Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
| Gloss Aluminium - Leaf Green GAL07 - Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
| Gloss Aluminium - Olympic Blue GAL13 - Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
| Gloss Aluminium - Silver Mist GAL11 - Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
| Gloss AluminiumTrue Blood GAL01
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
| Gloss Aluminium - Mermaid Green GAL05 - Design lakovaného hliníku.
Vysoce kvalitní polymerní vícevrstvá kalandrovaná vinylová fólie se stříbrným zadním povrchem a kanálky v lepidle pro uvolňování vzduchu.
TeckWrap Style 180 Series
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). We recommend steam vacuum or IRR heater for installation.
Thickness of film: 0.15mm
Thickness of film with release liner: 0.29mm
Type of film: High grade polymeric multilayered calendared vinyl film with silver back coating and air release channels
Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd)
Series: 180 series
Adhesive: Solvent polyacrylate
Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel)
180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch
Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating
Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place
Avg. indoor life: 4 years when followed rules of application and usage
Avg. outdoor life: 3 years when followed rules of application and use
Application: from +17°С to +25°С, usage from -55°С to +65°С
Dimensional stability: shrinkage less than 3%(matte), 4% (glossy)
Plastification: between 27%-35%
Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average)
Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005,
Test result: 5
Exposure cycle: ASTM D4329-13 cycle A
Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h
Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater
Application method: Standard methods for calendered films. No overstretching. Post heating
Post-heating temperature: 100℃ flat surfaces, 120℃ curves, and overlaps
Cure time: 24 hours above 15℃
Aftercare: PH neutral, Avoid hot wax or solvents
The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch
Implementation:
1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.
Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation
Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel
Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.
Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.
2. Wrapping must be done in clean room.
3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).
4. The recommended temperature for wrapping is 16-18 Celsius.
5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.
6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.
7. Use leeching technique on difficult surfaces.
8. Use method of relief cuts to decrease tension of vinyl film.
9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.
10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.
When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.
11. Post heat the surface over 100 Celsius after installation of vinyl film.
12. Apply edge sealer or transparent laminate film on edges of the film to protect them.
13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.
14. Wrapped vehicle can be washed only after 7 days.
15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.
|
Weight | ||||||
Dimensions | - | - | - | - | - | - |
Additional information |
Recenze
Zatím zde nejsou žádné recenze.