Mystic Chrome – Purple Blue Aguamarine MCH01

SKU: MCH01
Skladem
19 837 
Skladem

Přidat do oblíbených
Přidat do oblíbených
Přidat do oblíbených
Přidat do oblíbených
Další lidé se zajímají o tento produkt. 19 zákazník má produkt právě v košíku.
Možnosti dopravy SKU: MCH01 Kategorie: Štítky:

Zrcadlová chromová fólie: Mystic Chrome – Purple Blue Aguamarine MCH01

Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.

 

Popis

Zrcadlová chromová fólie: Mystic Chrome – Purple Blue Aguamarine MCH01

TeckWrap Style 180 Series

Conformable and flexible PVC material with silver coating. Suitable for car wrapping (or any other smooth or medium curved surface). Comes with a selection of 14 reflective colors to create the distinctive appearance and improve a car’s aesthetics. We recommend using a steam vacuum or IRR heater for installation.

Thickness of film: 0,11mm

Thickness of film with release liner: 0,29mm

Type of film: Polymeric vinyl film (silver coating) with air release channels

Series: 180 series

Adhesive: Henkel solvent based moderate adhesive

Release liner: White silicone-coated paper with double-sided polyethylene coating

Storing period: 3 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place

Indoor life: 4 years when followed rules of application and use

Outdoor life: 2 years when followed rules of application and use

Application: from +17°С to +25°С, usage from -35°С to +35°С

Dimensional stability: shrinkage less than 0,20%

Plastification: between 23%-31%

Package: Roll width 152 cm, length 18 m, weight 13 kg

Implementation:

1. TeckWrap 180 series – smooth surfaces
2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed.

Application stages:
1. Cleaning of surface
2. Right choice of film according to its implementation
3. Technological installation

Recommended Application tools
• High density felt squeegee
• Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives
• Professional temperature controllable heat gun
• Infrared Thermometer
• Gloves
• Felt block
• Towel

Surface cleaning rules
24 hours before installation
1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution.
2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol.
3. Cleaning of surface with abrasive clay to remove the rest of contamination.
4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals.
Right before installation
1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements.
2. Degreasing of surface, degreasing curves and corners.
3. Cleaning of dust from the surface with sticky anti-dust clothes.

Rules of technological installation:
1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film.

2. Wrapping must be done in clean room.

3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures).

4. The recommended temperature for wrapping is 16-18 Celsius.

5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%.

6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application.

7. Use leeching technique on difficult surfaces.

8. Use method of relief cuts to decrease tension of vinyl film.

9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements.

10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond.

When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces.
Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently.

11. Post heat the surface over 100 Celsius after installation of vinyl film.

12. Apply edge sealer or transparent laminate film on edges of the film to protect them.

13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours.

14. Wrapped vehicle can be washed only after 7 days.

15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.

 

 

Další informace

Značka

Teck Wrap

Podle barvy

,

Typ zboží

Vzhled fólie

Chromové, Lesklé

Recenze

Zatím zde nejsou žádné recenze.

Buďte první, kdo ohodnotí „Mystic Chrome – Purple Blue Aguamarine MCH01“

Vaše e-mailová adresa nebude zveřejněna. Vyžadované informace jsou označeny *

Quick Comparison

SettingsMystic Chrome - Purple Blue Aguamarine MCH01 removeMystic Chrome - Green Malachite MCH04 removeTeckWrap USA Carbon - Shiny Black 4D01N removeSuper Matte - Pink Lace CM07 removeTeckWrap USA wrapping fólie Zircon blue RB24 removeTeckWrap USA wrapping fólie Sea Sparkle remove
Image
SKUMCH01MCH04G4D-01-1CM07RB24CK103
Rating
Cena19 837 19 837 865 11 957 18 600 20 593 
Stock
Skladem
Skladem
Skladem
Skladem
Skladem
Skladem
AvailabilitySklademSklademSklademSklademSklademSkladem
Add to cart

Přidat do košíku

Přidat do košíku

Přidat do košíku

Přidat do košíku

Přidat do košíku

Přidat do košíku

DescriptionZrcadlová chromová fólie: Mystic Chrome - Purple Blue Aguamarine MCH01 Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.  Zrcadlová chromová fólie: Mystic Chrome - Green Malachite MCH04 Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.  
TeckWrap USA Carbon - Shiny Black 4D01N
Carbon 4D, profi design. Galaxy Black G4D-01N Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní..    
Super Matte - Pink Lace CM07 - Design fólie je velice matný. Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.      
TeckWrap USA wrapping fólie Zircon blue RB24
Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.
TeckWrap USA wrapping fólie Sea Sparkle
Role fólie návin: 18bm.Šíře 1,52m. Fólie TeckWrap prodáváme na celé role. V případě menšího množství volejte. Fólie na objednávku. Doba dodání standardně 5 dní.
ContentZrcadlová chromová fólie: Mystic Chrome - Purple Blue Aguamarine MCH01 TeckWrap Style 180 Series Conformable and flexible PVC material with silver coating. Suitable for car wrapping (or any other smooth or medium curved surface). Comes with a selection of 14 reflective colors to create the distinctive appearance and improve a car's aesthetics. We recommend using a steam vacuum or IRR heater for installation. Thickness of film: 0,11mm Thickness of film with release liner: 0,29mm Type of film: Polymeric vinyl film (silver coating) with air release channels Series: 180 series Adhesive: Henkel solvent based moderate adhesive Release liner: White silicone-coated paper with double-sided polyethylene coating Storing period: 3 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Indoor life: 4 years when followed rules of application and use Outdoor life: 2 years when followed rules of application and use Application: from +17°С to +25°С, usage from -35°С to +35°С Dimensional stability: shrinkage less than 0,20% Plastification: between 23%-31% Package: Roll width 152 cm, length 18 m, weight 13 kg Implementation:
1. TeckWrap 180 series – smooth surfaces 2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed. Application stages: 1. Cleaning of surface 2. Right choice of film according to its implementation 3. Technological installation Recommended Application tools • High density felt squeegee • Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives • Professional temperature controllable heat gun • Infrared Thermometer • Gloves • Felt block • Towel Surface cleaning rules 24 hours before installation 1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution. 2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol. 3. Cleaning of surface with abrasive clay to remove the rest of contamination. 4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals. Right before installation 1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements. 2. Degreasing of surface, degreasing curves and corners. 3. Cleaning of dust from the surface with sticky anti-dust clothes. Rules of technological installation: 1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film. 2. Wrapping must be done in clean room. 3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures). 4. The recommended temperature for wrapping is 16-18 Celsius. 5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%. 6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application. 7. Use leeching technique on difficult surfaces. 8. Use method of relief cuts to decrease tension of vinyl film. 9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements. 10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond. When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces. Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently. 11. Post heat the surface over 100 Celsius after installation of vinyl film. 12. Apply edge sealer or transparent laminate film on edges of the film to protect them. 13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours. 14. Wrapped vehicle can be washed only after 7 days. 15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.  
 
Zrcadlová lesklá chromová fólie: Mystic Chrome - Green Malachite MCH04 TeckWrap Style 180 Series Conformable and flexible PVC material with silver coating. Suitable for car wrapping (or any other smooth or medium curved surface). Comes with a selection of 14 reflective colors to create the distinctive appearance and improve a car's aesthetics. We recommend using a steam vacuum or IRR heater for installation. Thickness of film: 0,11mm Thickness of film with release liner: 0,29mm Type of film: Polymeric vinyl film (silver coating) with air release channels Series: 180 series Adhesive: Henkel solvent based moderate adhesive Release liner: White silicone-coated paper with double-sided polyethylene coating Storing period: 3 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Indoor life: 4 years when followed rules of application and use Outdoor life: 2 years when followed rules of application and use Application: from +17°С to +25°С, usage from -35°С to +35°С Dimensional stability: shrinkage less than 0,20% Plastification: between 23%-31% Package: Roll width 152 cm, length 18 m, weight 13 kg Implementation:
1. TeckWrap 180 series – smooth surfaces 2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed. Application stages: 1. Cleaning of surface 2. Right choice of film according to its implementation 3. Technological installation Recommended Application tools • High density felt squeegee • Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives • Professional temperature controllable heat gun • Infrared Thermometer • Gloves • Felt block • Towel Surface cleaning rules 24 hours before installation 1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution. 2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol. 3. Cleaning of surface with abrasive clay to remove the rest of contamination. 4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals. Right before installation 1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements. 2. Degreasing of surface, degreasing curves and corners. 3. Cleaning of dust from the surface with sticky anti-dust clothes. Rules of technological installation: 1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film. 2. Wrapping must be done in clean room. 3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures). 4. The recommended temperature for wrapping is 16-18 Celsius. 5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%. 6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application. 7. Use leeching technique on difficult surfaces. 8. Use method of relief cuts to decrease tension of vinyl film. 9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements. 10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond. When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces. Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently. 11. Post heat the surface over 100 Celsius after installation of vinyl film. 12. Apply edge sealer or transparent laminate film on edges of the film to protect them. 13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours. 14. Wrapped vehicle can be washed only after 7 days. 15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.  
 
TeckWrap USA Carbon - Shiny Black 4D01N
Carbon 4D, profi design. Shiny Black 4D-01N Fólie má matný nelakovaný povrch. Shiny Black 4D má design, jako skutečný CARBON!!! Společnost TECKWRAP USA se specializuje na vlastní výrobu wrap fólií. Fólie se používají pro celopolep automobilů, dekorace a tuning. S fólií TeckWrap zabalíte (polepíte) jak jednoduché tak velice složité 3D tvary. Fixování paměti fólie TeckWrap se provádí horkovzdušnou pistolí a to nahřátím aplikované fólie na min. 80 - 120°C. TeckWrap zaručuje vynikající kvalitu za přijatolnou cenou. Tím zůstává před konkurencí. Fólie TeckWrap se používají hlavně v automobilovém průmyslu pro celkové zabalení automobilů, dekoraci a ochranu laku. TeckWrap nabízí více jak 200 odstínů barev. Lesklé chromové fólie, matné chromové fólie, dekorace kovu, hliníku, perleťové fólie, metalické matné a lesklé fólie, chameleon fólie, přechodové chromové fólie.... Fólie TeckWrap jsou k dispozici v rolích délek 18bm. Vaše spokojenost je zaručena!
Tecnická data:
Reliable polymeric PVC for partial application. Designed for wrapping of smooth surfaces or elements of medium difficulty in wrapping; spoilers, mirrors, etc. Memory killed at over 80 Celsius with post-heating. Thickness is 150 micron. Dimensional stability -2-3mm in 1 year. The size of carbon cells is medium. Lines are straight and stylish. This is by far the most popular vinyl film. Unlike those cheap carbon patterns, true 3D texture of the film reveals genuine look of dry carbon fiber. The weave reflects light the same way as the actual carbon fiber would. Thickness of film (C=10 micron): 15C±0.5C Thickness of film with release liner: 33C±0.5C Type of film: Medium grade polymeric calendered vinyl film with air release channels Colors: Black Series: 180 series Glue: Solvent based adhesive, transparent, origin: Taiwan. Release liner: White silicone-coated paper with double-sided polyethylene coating Storing period: 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Indoor life: 4 years when followed rules of application and use Outdoor life: 2 years when followed rules of application and use Application: from +5°С to +30°С, usage from -30°С to +50°С Dimensional stability: shrinkage less than 2% Plastification: between 28%-38% Breaking Strength: 23.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-05 6.4 N/10mm (Average) Test Method: ASTM D3330/D3330-04 Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005, Test result: 3-4 Exposure cycle: ASTM D4329-13 cycle A, Lamp type: UVA-340 8h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 44h Package: Roll width 152 cm, length 18 m, weight 14 kg The images, colours and finishes on screen are approximate. For the real representation of the product always check the color swatch.
 
Super Matte - Pink Lace CM07 - Design fólie je velice matný. Měkké a přizpůsobivé wrapping fólie, které jsou vyrobené z PVC, fólie obsahují kvalitní složky a lepidlo. Lepidlo má nízkou počáteční lepivost a získává svou pevnost za 24 hodin. Matné převleky by měly být dostatečně zataveny a zahřáty. Tloušťka vinylu je 130 mikronů. Dodává se v různých barvách. Touto matnou fólií TeckWrap dáte Vašemu vozu elegantní vzhled.
Thickness of film (C=10 micron): 14-15C±0.5C Thickness of film with release liner: 31-32C±0.5C Type of film: Medium grade polymeric calendered film with air release channels Colors: Black, Vivid Orange, Ice Blue, Racing Red, Pink Lace, Toxic Green Series: 180 series Glue: Henkel solvent based adhesive Release liner: White silicone-coated paper with double-sided polyethylene coating Storing period:  3 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Indoor life: 5 years when followed rules of application and use Outdoor life: 3 years when followed rules of application and use Application: from +5°С to +30°С, usage from -30°С to +50°С Dimensional stability: shrinkage less than 0,20% Plastification: between 25%-32% Breaking Strength: 30.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-05180º Peel Strength, to steel panel: 9 N/10mm (Average) Test Method: ASTM D3330/D3330-04 Light Ageing in UV Exposure: Test Method ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005, Test result: 4-5 / Exposure cycle: ASTM D4329-13 cycle A, Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/(m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 48h Package: Roll width 152 cm, length 20 m, weight 15 kg
Implementation:
1. TeckWrap 180 series – smooth surfaces 2. TeckWrap 190 series – smooth surfaces, curved surfaces only when rules of calandered and hybrid vinyl film application are followed. Application stages: 1. Cleaning of surface 2. Right choice of film according to its implementation 3. Technological installation Recommended Application tools • High density felt squeegee • Cutter (knives with 30 and 45 degree blades). We recommend OLFA, Tajima and Samurai knives • Professional temperature controllable heat gun • Infrared Thermometer • Gloves • Felt block • Towel Surface cleaning rules 24 hours before installation 1. Clean the surface with soap liquid. Hand cleaning of organic and nonorganic wastes, removal of exhausted solution. 2. Clean away any petrochemical contaminates (tar, oil, grease, etc.). Use a good automotive cleaner and wax remover. Wipe down surface with isopropyl alcohol. 3. Cleaning of surface with abrasive clay to remove the rest of contamination. 4. Drying of elements. To dry the surface, use a dry cloth or paper towel. Make sure that the surface, edges, corrugations, hollows and joints of the vehicle are completely dry. Carefully remove remaining humidity under rubber seals. Right before installation 1. Checking of surface for contaminations. Cleaning of dirt after dismantling of elements. 2. Degreasing of surface, degreasing curves and corners. 3. Cleaning of dust from the surface with sticky anti-dust clothes. Rules of technological installation: 1. Keep the roll 24 hours in a place where it will be cut in order to climates the roll. Work with a cold film in a place with normal temperature can cause deformations on the film. 2. Wrapping must be done in clean room. 3. Moisten the room floor in winter period to minimize dust (anti-electrostatic measures). 4. The recommended temperature for wrapping is 16-18 Celsius. 5. Don’t overstretch vinyl film. We recommend not stretching any film, including textured ones, over 10%. 6. We recommend cold wrapping method with installation of calendared and hybrid films. Use dry method of application. 7. Use leeching technique on difficult surfaces. 8. Use method of relief cuts to decrease tension of vinyl film. 9. Use pre-stretch technique for wrapping of bumpers, mirrors, door handles and other curved elements. 10. Use glue promoter for surfaces with low energy and compound curves. We recommend 3M 94 and Probond. When glue promoter is not used on compound curves we recommend wrapping in overlaps with pieces. Please keep in mind that various automotive plastics contain in part release agents and softeners. These can be released (gas emission) when exposed to heat, e.g. through strong sunlight and there by influence the adhesive effect bubble formation of the film. Same may happen if the car surface was painted recently. 11. Post heat the surface over 100 Celsius after installation of vinyl film. 12. Apply edge sealer or transparent laminate film on edges of the film to protect them. 13. After installation one should keep the vehicle in room temperature (18-23 Celsius) for at least 24 hours. 14. Wrapped vehicle can be washed only after 7 days. 15. It is forbidden to ride under rain or snow in 48 hours after installation of vinyl film.  
TeckWrap USA wrapping fólie Zircon blue RB24
Conformable material with stable color pigments. Suitable for full car wrapping (or any other smooth or curved surface). Comes in 25 gloss colors Thickness of film (mm): 0.17-0.19mm Thickness of film with release liner: 0.34-0.35mm Type of film: High grade polymeric multilayered calendared vinyl film with air release channels   Width & Length: 1.52m*18m (59.8"* 708,6", 4.98ft*59ft, 1.66yd* 19,6yd) Series: 190 series Adhesive: Solvent polyacrylate Adhesive performance properties: (1mil adhesive on 1mil material, bonded to stainless steel panel) 180°Peel (PSTC-101), 20 minute bond – 2.2 lb/inch, 24 hour bond – 3.5 lb/inch Release liner: Kraft white silicone-coated, paper with double-sided polyethylene coating Storing period (shelf life): 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Avg. indoor life: 4 years when followed rules of application and usage Avg. outdoor life: 3 years when followed rules of application and use Application: from +17°С to +25°С, usage from -55°С to +65°С Dimensional stability: shrinkage less than 4% Plastification: between 27%-35% Breaking Strength: 22.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-057.4 N/10mm (Average) Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005, Test result: 5 Exposure cycle: ASTM D4329-13 cycle A, Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 49h Recommended application tools: Squeegee, buffer, knife, masking tape, heat gun, magnets, gloves, IRR thermometer, IRR heater Application method: Standard methods for calendered films. No overstretching. Post heating Post-heating temperature: 110℃ flat surfaces, 130℃ curves, and overlaps Cure time: 24 hours above 10℃ Aftercare: PH neutral, Avoid wax or solvents The images, colors, and finishes on screen are approximate. For the real representation of the product always check the color swatch.
TeckWrap USA wrapping fólie Sea Sparkle
Fascinating glossy wraps. The finished product gleams, just like diamond. Good for wrapping of smooth surfaces or elements of medium difficulty in wrapping; roofs, mirrors, etc. Different colors are available. Memory killed at over 85 Celsius with post-heating. Thickness is 160 micron. Dimensional stability - 2mm in 1 year. Thickness of film (C=10 micron): 16C±0.5C Thickness of film with release liner: 34C±0.5C Type of film: Medium grade polymeric calendered film with air release channels Colors: Aurora Pink, Aurora White, Blue Sonata, Sea Sparkle, Sparkling Black, Sparkling White Series: 190 series Glue: Henkel solvent based adhesive Release liner: White silicone-coated paper with double-sided polyethylene coating Storing period: 2 years if stored in +10°С to +20°С, relative humidity 50%, in original package, away from direct sun light, clean and dry place Indoor life: 5 years when followed rules of application and use Outdoor life: 3 years when followed rules of application and use Application: from +17°С to +25°С, usage from -55°С to +65°С Dimensional stability: shrinkage less than 2% Plastification: between 28%-38% Breaking Strength: 23.7 N/10mm (Average) Test Method: ASTM D3759/D3759M-056.4 N/10mm (Average) Test Method: ASTM D3330/D3330-04 Light Ageing in UV Exposure: Test Method: ASTM D4329-13 Cycle A & ISO 105-A02:1993/Cor.2:2005, Test result: 3-4 Exposure cycle: ASTM D4329-13 cycle A, Lamp type: UVA-3408h UV at (60±2.5)℃ BPT, 0.89 W/ (m2•nm)@340nm, 4h condensation at (50±2.5)℃ BPT, Exposure duration: 44h Package: Roll width 152 cm, length 18 m, weight 14 kg The images, colors and finishes on screen are approximate. For the real representation of the product always check the color swatch.
Weight
Dimensions------
Additional information
Značka

Teck Wrap

Podle barvy

,

Typ zboží

Vzhled fólie

Chromové, Lesklé

Značka

Teck Wrap

Podle barvy

, ,

Typ zboží

Vzhled fólie

Chromové, Lesklé

Značka

Teck Wrap

Podle barvy

Typ zboží

Vzhled fólie

Carbon, Matné

Značka

Teck Wrap

Podle barvy

Typ zboží

Vzhled fólie

Matné

Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Cena
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare